Manufacturer of POS Systems: POS-5700 User's Manual
 Home > Product > POS Terminals > POS System 5700 > User's Manual

POS-5700 Series

General Information



The purpose of this user’s manual is to provide general information on TYSSO POS System 5700 Series Touch Screen POS terminal and to show the users how to configure the hardware-related configurations. The information in this manual is subject to change without notice due to rapid improvement on IT technology. The users can get the most up to date information from our web sites:



This manual has been examined for accuracy. While precaution has been taken in the preparation of this manual, neither the manufacturer takes no liability for errors or omissions nor assume any responsibility for damage(s) incurred directly or indirectly from errors, omissions, or discrepancies of this manual. IN NO EVENT WILL THE VENDOR BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF THE POSSIBILITY OF SUCH DAMAGES HAS BEEN ADVISED. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, OR RECOVERING SUCH HARDWARE, SOFTWARE OR DATA.



The touch screen POS terminal has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. This equipment can generate and radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interface will not occur under particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interface by one or more of the following measures:


  • Reorient or relocate the receiving antenna

  • Increase the distance between the equipment or device

  • Connect the equipment to an outlet other than the receiver’s

  • Consult a dealer or an experienced radio/TV technician for assistance





The system is provided with a battery-powered Real-Time Clock circuit. There is a danger of exposing and personal injury if the battery is incorrectly replaced or mistreated. Do not attempt to disassemble the battery, immerse it in the water or expose it to fire.



If the POS System 5700 series machine is disassembled by any person other than the authorized technicians, the warranty will be terminated. The users should consult his/her dealer for any technical problems. Warranty does not cover any damage caused by improper use.



TYSSO is a registered trademark of FAMETECH INC.

Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.



  • Read all these instructions carefully.

  • Use only parts, especially power adapter, recommended by the manufacturer; unapproved parts may be hazardous.

  • Before plugging the power cord into the AC inlet of the power supply unit, make sure the voltage (either 110V or 220V) is properly applied to the power switch. Improper voltage will cause damage to the power supply unit.

  • Power off the system and remove the power adapter while cleaning the system.

  • Before powering on the system, check if all the peripherals are firmly installed.

  • Do not use the system near water, such as a bathtub, a washbowl, a kitchen sink, a laundry tub, and a swimming pool. Keep the system away from direct sunlight, a heating or a radiator.

  • Do not place the system on an unstable cart, stand or table. If the machine falls, it may injure a person or cause serious damage to the appliance.

  • The system is equipped with a three-wire grounded plug with a third (grounding) pin. This is a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install a correct outlet, or use an adapter to ground the appliance safely. Do not leave out the safety purpose of the grounded plug.

  • Do not allow anything to rest on the power cord. Do not locate the system where people may walk on the cord.

  • Do not make the power outlet and extension cords overload. Overload can result in fire or electric shock.

  • Do not push any object into the computer cabinet. Dangerous voltage points may be touched and the parts may be shorted out resulting in fire or electric shock.

  • Do not attempt to service the system on your own. Opening or removing cover can expose you to dangerous voltage or other hazards.

  • Power off the system before installing or removing non-PNP (plug and play) devices.

  • If any of the following situations occurs, unplug the systems from the power outlet immediately and consult with a qualified service person:

  1. The power cord or plug is damaged or frayed.

  2. Liquid is spilled into the system.

  3. The system is dropped or the cabinet is damaged.

  • When the system is not in use, cover the system and store it with care.




Version 1.0

Copyright Fametech Inc. (TYSSO) 2008

        Other POS Terminals



Point Of Sale 5000   Point Of Sale 5700

Point Of Sale 7000

CCD | Laser Gun | Fixed Reader | Wands | Slot Reader  | OEM Modules | Portable | Decoder & Accessories | Omnidirectional

Barcode Scanner | Magstripe Card Reader / Writer | POS Customer Display  |  POS Keyboard | Touchscreen POS System
Cash Drawer | Serial-Ethernet Converter | Receipt Printer


Copyright 2008 Fametech Inc.(Tysso)                                                                                              Home | Products | Contact

CCD Barcode ScannersMagnetic Stripe Card ReadersReceipt PrintersSerial-Ethernet Converter