The purpose of
this user’s manual is to provide the general information about TYSSO POSmall
POS terminal. The manufacturer apologize that the information in this manual is
subject to change without notice due to the rapid improvement on IT technology. The user can always get the most up to
date information through our web sites:
http://www.tysso.com.tw
This manual has been examined for accuracy. While precaution has been taken in the
preparation of this manual, The manufacturer takes no liability for error or
omissions. Neither do manufacturer
assumes any responsibility for damage(s) incurred directly or indirectly from
errors, omissions, or discrepancies of this manual. IN NO EVENT
WILL THE VENDOR BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN
PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR
DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING,
REPLACING, OR RECOVERING SUCH HARDWARE, SOFTWARE OR DATA.
The POS terminal has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interface
in a residential installation. This equipment generates and can radiate radio
frequency energy and, if not installed and used according to the instructions,
may cause harmful interference to radio communications. However, there is not
guarantee that interface will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the user is encouraged to
try to correct the interface by one or more of the following measures:
l Reorient or
relocate the receiving antenna
l Increase the separation
between the equipment or device
l Connect the
equipment to an outlet other than the receiver’s
l Consult a dealer
or an experienced radio/TV technician for assistance
IMPORTANT NOTICE
.
If the POS terminal is opened by any person other than the authorized technicians,
the warranty will then automatically terminated. The user should consult his/her dealer
for any technical problems. Warranty voids if the user does not follow the
instructions in application of this product. The manufacturer is by no means
responsible for any damage or hazard caused by improper use.
TRADE
MARKS AND SERVICE MARKS
TYSSO is a registered trademark of FAMETECH INC.
Other brand and product names are trademarks and registered trademarks and
service marks of their respective owners.
© Copyright Fametech Inc. (TYSSO) 2003
Safety Important Information
²
Read all of these instructions carefully.
²
Use only parts, especially power adapter, recommended
by the manufacturer; unapproved parts may be hazardous.
²
Before plug the power cord on the AC inlet of the power
supply unit, please make sure that power switch is on correct voltage either
115V or 230V to avoid the damage of the power supply unit.
²
Power off the POS terminal and remove the power adapter
when clean the system.
²
Before power on the POS terminal, please check if
all the peripheral are all install firmly.
²
Do not use the POS terminal near water, for example
near a bathtub, washbowl, kitchen sink, or laundry tub or near a swimming pool.
Avoid installing the system exposed to direct sunlight, near a heating or a
radiator.
²
Do not place the POS terminal on an unstable cart,
stand or table. If the machine falls, it could injure a person or cause serious
damage to the appliance.
²
The POS terminal is equipped with a three-wire
grounded plug, a plug with a third (grounding) pin. This is a safety feature.
If your outlet does not accommodate the three-wire plug, have an electrician
install the correct outlet, or use an adapter to ground the appliance safely.
Do not defeat the safety purpose of the grounded plug.
²
Do not allow anything to rest on the power cord. Do
not locate the POS terminal where people may walk on the cord.
²
Do not overload power outlet and extension cords.
Overload can result in fire or electric shock.
²
Do not push any object into the POS terminal
cabinet. It could touch dangerous voltage points or short out parts resulting
in a fire or electric shock.
²
Do not attempt to service the monitor by yourself, opening
or removing cover can expose you to dangerous voltage or other hazards.
²
The POS terminal must not be operated in an
environment with restricted ventilation.
²
Unplug the systems from the power outlet immediately
and refer servicing to qualified service personnel under the following
conditions:
u
When the power cord or plug is damaged or frayed.
u
If liquid has been spilled into the system.
u
If the system has been dropped or the cabinet has
been damaged.
²
When the machine is not in use, please do cover the
POS terminal and store with care.
1.
Unpacking
1.1)
Standard Unit
1.2)
Available optional peripherals/components
2.
POSmall Overview
3.
Setting to select provide DC power supply on COM 3
and COM 4
4.
CD ROM disk
5.
LED
indicators
1. Unpacking
The following part list is for reference only. Due to different
options, the parts content in the package may be difference. If any of the
items are damaged or missing, please contact your supplier immediately. Please keep the packing materials for
further usage such as moving or shipping the system and etc.
1.1) Standard Unit
l
POS-500 x 1
l
Power supply unit x 1
l
AC power cord x 1
l
User’s manual x 1
l
CD Disk
l
Stand x 2 set
l
Key x 2
1.2) Available Optional Peripherals/components
l
DDR RAM
l
CPU with fan
l
3.5” HDD
l
Slim type CD ROM
l
IrDA connector
l
VGA monitor
l
Cash Driver
l
Barcode reader
l
Magnetic card reader
l
Customer display
l
POS keyboard
l
POS printer
2.
POSmall Overview
This is a durable, smart and compact sized P4 level POS
terminal for retail/POS applications. For the security requirements of the POS
business, a lockable front panel is provided to seal the CD ROM and the on/off
switch to secure data and avoid the unintended power off the system. In the POS
terminal, there are 4 COM ports, among the ports, COM 3 and COM 4 ports are
able to select to provide DC power support for eliminating the usage of
external power supply for POS devices. To up-grade or for after service
purposes, just replace a mother board with mini flex ATX form factor into the
case.
Front view 1.
Front view 2.
Rear view
3.
Setting to select the DC power supply on COM 3 and
COM 4
The default setting of the
COM 3 and COM 4 are not provided DC power on the two com ports.
4.
CD ROM Disk 1.6 (or later version)
The bundled CD ROM DISK
provides drivers applicable to the POS terminal and our other products. If no
POS-500 subdirectory is found on the CD ROM disk, please visit our web site www.fametech.com.tw to down lord it.
5.
LED indicators
There are two LED indicators on the front of the terminal. The RED LED
indicates power on and the green LED indicates while LAN is on working.
There is another green LED on the power connector to the terminal. The
green LED on indicates the power adapter at on status.
POS System Index : 12.1" CubicPOS | 15" CubicPOS | Barebone POS Unit | TFT Touchscreen POS Monitor | 9" CRT Mono.
POS Terminal FAQ | TYSSO Product Links:
Barcode Scanner | Magstripe Card Reader / Writer |
POS Customer Display |
POS Keyboard
Touchscreen POS System | Cash Drawer |
Serial-Ethernet Converter |
Receipt Printer
| Links to Other Sites